14-oz. Cartridge
14-oz. Cartridges (case of 10)
14-oz. Cartridges (case of 40)
35-lb. Lug
120-lb. Keg
400-lb. Drum
PRODUCT DESCRIPTION
AMSOIL Synthetic Multi-Purpose Greases are
qualified against the highest grease standards and are designed for multiple
use applications. Composed of premium quality synthetic base oils and
lithium complex thickeners, Multi-Purpose Greases provide superior film
strength, shear resistance, adhesion properties and mechanical stability,
and they excel in temperature extremes by providing excellent oxidation
stability, high temperature dropping points and low temperature torque
values and pumping capabilities. AMSOIL Synthetic Multi-Purpose Greases are
formulated with oil soluble extreme-pressure additives for heavy loads, as
well as oxidation and corrosion inhibitors that impart good oxidation
stability and rust protection.
PERFORMANCE FEATURES
- High dropping point of 500°F+
- Resists thermal and oxidation degradation
- Excellent water-washout resistance
- Good low temperature pumpability and torque values
- Adhesive and shear stable to prevent squeeze out
Applications or Requirements
- GLB (#1) ASTM D-4950 (NLGI) Service GC/LB
- GLB (#1) Cincinnati Milicron P-72 Spec
APPLICATION
RECOMMENDATION
AMSOIL Synthetic Multi-Purpose Grease grade #1
is recommended in manual or automatic lubricating systems. NLGI #1 (GLB) has
better mobility and is the preferred choice for colder applications,
automatic lubrication systems with long pumping runs and gear box
applications (where recommended by manufacturer).
The correct consistency grade of AMSOIL Synthetic
Multi-Purpose Grease is recommended in heavy and light duty applications
found in manufacturing plants, automobiles, agricultural and construction
equipment.
These include, but are not limited to, roller bearings,
plain bearings, thrust bearings, gears, electric motors, presses, winches,
bushings, wheel bearings, chassis lubrication, universal joints, ball
joints, tie-rod ends, and steering knuckles. AMSOIL Synthetic Multi-Purpose
Greases are suitable for use up to 350 degrees F. When operating at elevated
temperatures, frequent regreasing may be required.
AMSOIL Synthetic Multi-Purpose Greases are
compatible with many other types of greases. However, it is recommended that
when changing greases, the equipment be cleaned of the old grease when
possible or flushed with a liberal amount of Multi-Purpose Grease while the
mechanism is in operation. Closely monitor the system for any
inconsistencies. Grease compatibility questions should be referred to your
AMSOIL representative or AMSOIL Inc.
APPLICATION
MAINTENANCE
Maintaining a clean work environment is
important when equipment greasing is performed. Wipe grease fittings clean
prior to injecting grease to prevent contaminant ingestion. Maintain bearing
housings one-third to one-half full of grease. Do not over-grease, as
excessive heat buildup can result. Supplement standard grease maintenance by
periodically cleaning and packing housings with fresh grease on an
established maintenance schedule.
| Typical Technical
Properties |
| Synthetic GLB Grease |
GLB |
NLGI GC/LB |
| Thickener |
lithium complex |
NR |
| NLGI consistency grade |
1 |
NR |
| NLGI performance grade |
GC-LB |
NR |
| Penetration - ASTM D 217 (25°C [77°F], 0.1 mm)
worked 60 strokes |
310-340 |
220-340 min |
| Dropping point, °F[°C] - ASTM D2265 |
500 [260] |
428 [220] min |
| High temperature life, hours - ASTM D 3527 |
140 |
80 min |
| Oxidation stability, psi - ASTM D 942 (100 hr/300
hr) |
0/5 |
NR |
| Water washout, percent - ASTM D 1264 |
5.8 |
15 max |
| Rust and corrosion - ASTM D 1743 |
pass |
pass |
| Oil separation, percent loss - ASTM D 1742 (24
hours, 25°C [77°F] |
3.4 |
6.0 max |
| Leakage, g lost - ASTM D 4290 |
7.8 |
10 max |
| Four ball wear test, mm scar - ASTM D 2266 |
0.43 |
0.60 max |
| Fretting wear, mg - ASTM D 4170 |
3.5 |
10 max |
| Four ball EP, kgf - ASTM D 2596
Weld point
Load wear index
|
315
49
|
200 min
30 min
|
| Timken OK load test, lbs - ASTM D 2509 |
45 |
NR |
| Low temperature torque, N*m - ASTM D 4693 (-40°C
[-40°F]) |
0.50 |
15.5 max |
| LT-37 pumpability, g/min (60°F/0°F [16°C/-18°C]) |
855/29 |
NR |
| Copper corrosion - ASTM D 4048 |
1B |
NR |
| Disc brake wheel bearing specifications
Ford ESA-M1C 198A
Chrysler MS-3701
|
NA
NA
|
NR
NR
|
| Oil viscosity:
40°C [104°F], cSt
100°C [212°F], cSt
|
151
19.2
|
NR
NR
|
| Flash point, °F[°C] - ASTM 92 |
450[232] |
NR |
| Color |
red |
NR |
| Texture |
smooth with tack |
NR |
NA: Not applicable
NR: Not required for NLGI GC-LB labeling
|
