5-Gallon Pail
55-Gallon Drum
PRODUCT DESCRIPTION
AMSOIL Synthetic Anti-Wear Biodegradable Hydraulic Oil (TBI) is a
premium lubricant designed to biodegrade to its natural state when subjected
to sunlight, water and microbial activity. Because it is formulated with
ashless additives that do not contain heavy metals, AMSOIL Biodegradable
Hydraulic Oil has a very low toxicity level.
AMSOIL Biodegradable Hydraulic Oil incorporates very
high-quality synthetic base oils that provide thermal stability, even though
they are biodegradable. It also contains anti-wear additives that have been
thoroughly tested and qualified against stringent hydraulic oil standards,
including Denison HF-0, HF-1 and HF-2; Vickers M-2950-S and I-286-S and
Cincinnati Milacron P-68 and P-70. AMSOIL Biodegradable Hydraulic Oil
provides optimum protection for hydraulics, helping to prevent pump wear and
rusting of critical components. It also contains antioxidants that increase
oil life and foam inhibitors that quickly release air from the oil.
Based on high-quality, synthetic oil chemistry that better
withstands heat and lasts longer, AMSOIL Biodegradable Hydraulic Oil
outperforms vegetable oil-type, biodegradable hydraulic oils, promoting
problem-free operation.
APPLICATION
RECOMMENDATION
AMSOIL Synthetic Biodegradable Hydraulic Oil is recommended for gear,
vane and piston stationary and mobile hydraulic systems. It is a
multi-viscosity, SAE 5W-20 oil and is recommended for use in place of either
ISO-32 or ISO-46 hydraulic oils.
AMSOIL Biodegradable Hydraulic Oil is essentially compatible
with typical hydraulic oils, and small amounts of contamination (lines,
residue) are acceptable. However, it is recommended systems be drained prior
to installing TBI. Excessive system contamination will minimize its
biodegradability effectiveness.
AMSOIL TBI is especially well-suited for applications where
environmental contamination due to leaking or blown hydraulic lines presents
an environmental hazard. AMSOIL Biodegradable Hydraulic Oil has been tested
and found compatible with Nitrile (Buna-N), Poly Acrylate, Fluorocarbon
(Viton) and Silicone seals which are commonly found in hydraulic systems.
The ability of AMSOIL TBI to extend drain intervals and
excel in performance is subject to operating conditions and maintenance
practices. Monitoring by oil analysis is recommended.
PERFORMANCE FEATURES
- 80% Biodegradable Within 21 days (CEC L-33-A-94)
- Thermally Stable
- Resists Oxidation
- Anti-Rust and Anti-Foam
- -69°F Pour Point For Cold Temperature Performance
- Outperforms Vegetable-Type Bio-Hydraulic Oils
AMSOIL PRODUCT
WARRANTY
AMSOIL Industrial Lubricants are formulated to exceed accepted
industry specifications. AMSOIL warrants that the use of its lubricants will
not cause mechanical damage to any mechanically-sound equipment when AMSOIL
products are used in full compliance with the company’s recommendations.
However, the purchaser is responsible for determining if these
specifications are adequate and proper for the intended application. The
AMSOIL warranty is limited to lubricant performance consistent with
indicated specifications. No additional warranty, expressed or implied, can
be made. For additional warranty information see the
AMSOIL Waranty Page.
AMSOIL PRODUCT AVAILABILITY
AMSOIL products are available in 5-gallon pails, 55-gallon drums, 275-gallon
totes and bulk quantities.
AMSOIL Industrial Lubricants are stocked in Superior,
Wisconsin and in select regional distribution centers throughout the United
States and Canada. AMSOIL will stock additional quantities of lubricants or
special-order products based on customer requests and regional demands. For
applications and recommendations, contact your local AMSOIL Dealer or the
AMSOIL Technical Services Department.ications and recommendations, contact
your local AMSOIL industrial sales representative or AMSOIL INC.
|
Typical Technical Properties
|
| Synthetic TBI ISO 32/46 Biodegradable
Hydraulic Oil |
TBI |
| ISO VG - ASTM D-2422 |
32/46 |
| SAE Grade |
5W-20 |
| Viscometrics 100°C, cSt - ASTM D-445 |
7.3 |
| Viscometrics 40°C, cSt - ASTM D-445 |
40.1 |
| Viscosity Index (VI) - ASTM D-2270 |
149 |
| Specific Gravity - ASTM D-1298 |
0.9646 |
| Density - ASTM D-1298 |
8.033 |
| Four-Ball Wear Test - ASTM D-4172 (40 kg, 1200
rpm, 75° C, 60 min.) |
0.40 |
| Flash Point °C (°F) - ASTM D-92 |
256°C (493°F) |
| Fire Point °C (°F) - ASTM D-92 |
282°C (540°F) |
| Pour Point °C (°F) - ASTM D-97 |
-56°C (-69°F) |
| Copper Strip Corrosion Test - ASTM D-130 |
1A |
| Foam - ASTM D892 |
|
Sequence I
|
0/0 |
Sequence II
|
0/0 |
Sequence III
|
0/0 |
| Demulsibility - ASTM D1401 Oil/Water/Cuff
(minutes) |
40/40/0 (15) |
| Dielectric Strength, KV - ASTM D-887 |
36KV |
| Biodegradability % - CEC L-32-A-94 |
80 |
