1-Quart Bottle
1-Quart Bottles (case of 12)
2.5-Gallon Bottle
2.5-Gallon Bottles (case of 2)
30-Gallon Drum
55-Gallon Drum
Transmission Fluid Evacuation Service:
Bulletin
from Filter Manufacturers Council
ATF and Transmission Filter
Change Procedures
PRODUCT DESCRIPTION
AMSOIL Synthetic Fuel Efficient Automatic Transmission Fluid (ATL) is
engineered to exceed the requirements of GM, Ford and Toyota where
low-viscosity oil is required. The highly-specialized properties of this
light-bodied fluid provide outstanding performance without compromising
protection, even in severe operating conditions.
Automatic transmissions have become
increasingly complex as vehicle manufacturers strive to improve efficiency
while satisfying consumer demands. Smaller, smoother-shifting transmissions
with longer fluid life capabilities and heavier load capacities are now
standard. Traditional ATFs, however, are unable to meet these extreme
requirements, and new fluids have emerged with each new advancement in
transmission engineering. AMSOIL, with its original introduction of a
synthetic ATF in 1980, remains the leader in transmission fluid quality.
AMSOIL Synthetic Fuel Efficient Automatic Transmission Fluid is formulated
with the highest-quality components to exceed the most stringent industry
standards. The quality and performance of AMSOIL Synthetic ATF is
guaranteed.
Fully Fortified
• Anti-wear/extreme-pressure
agents—Extend gear life
• Durable friction modifiers—Anti-shudder
• Anti-oxidants—Extend fluid life
• Seal conditioners—Reduce leaks
• Detergents and dispersants—Keep clean and control deposits
• Corrosion inhibitors—Control rust
• Anti-foam agents—Improve hydraulic function
EXCEPTIONAL HOT- AND COLD-TEMPERATURE
PERFORMANCE
Thermal Stability – Hot temperatures are no excuse for poor
reliability. Naturally heat-resistant and heavily fortified with
anti-oxidants, AMSOIL Synthetic Fuel Efficient Automatic Transmission Fluid
exceeds the most demanding oxidation requirements. It delivers outstanding
protection against sludge and varnish deposits that clog narrow oil passages
and contribute to clutch glazing. AMSOIL Fuel Efficient ATF protects
hot-running transmissions.
Cold-Temperature Fluidity –
Cold, thick automatic transmission fluid lengthens shift times and reduces
energy efficiency (fuel economy). AMSOIL Synthetic Fuel Efficient ATF is
wax-free and delivers extraordinary cold-flow per formance (<-60°F pour
point). It helps improve shifting response and energy efficiency while
reducing warm-up times.
OUTSTANDING WEAR PROTECTION
Varying speeds and loads causes torque multiplication and extreme stress on
gears and bearings. To prevent wear damage resulting from insufficient fluid
film, AMSOIL Synthetic Fuel Efficient ATF is formulated with high film
strength (shear stability) and a select anti-wear/extreme-pressure additive
that develops a boundary layer of protection between metal surfaces. Even
though AMSOIL Synthetic Fuel Efficient Automatic Transmission Fluid is a
low-viscosity, fuel-efficient fluid, it has demonstrated its ability to
protect as well as or better than higher-viscosity fluids in the most severe
industry tests.
FRICTION DURABILITY
Today’s transmissions are smaller and must withstand higher horsepower and
torque while delivering smoother shifts, all with longer fluid life
recommendations. AMSOIL Synthetic ATF is formulated with friction modifier
additives that deliver outstanding clutch-holding capacity (static
friction), torque-transfer ability (dynamic friction) and anti-shudder
properties (slipping torqueconverter clutches).
EXTENDS FLUID SERVICE LIFE
Modern transmissions are smaller in design, yet are called upon to deliver
smoother shifts and longer fluid-life capabilities in higher-horsepower and
higher-torque conditions. AMSOIL placed great emphasis
on developing a fluid to effectively address the complex demands related to
friction. AMSOIL Synthetic Fuel Efficient Automatic Transmission Fluid
delivers outstanding clutch-holding capacity (static friction), torque
transfer ability (dynamic friction) and anti-shudder properties (slipping
torque-converter clutches).
APPLICATIONS
AMSOIL Synthetic Fuel Efficient Automatic Transmission Fluid is recommended
for automatic transmissions and other applications requiring DEXRON® VI,
MERCON® LV, SP or Toyota WS.
AMSOIL Synthetic Fuel Efficient Automatic Transmission
Fluid is backward compatible and replaces DEXRON® III fluids in older GM
automatic transmissions. (DEXRON® VI specification supersedes the obsolete
DEXRON® III in GM vehicles.)
*Not for use with CVT or Ford Type F applications.
EXTENDED FLUID SERVICE LIFE
Most drivers are unaware that transmissions commonly operate under severe
service and require shorter fluid drain intervals. AMSOIL Synthetic Fuel
Efficient Automatic Transmission Fluid is a long-life fluid capable of
extended service intervals. It provides an extra margin of protection,
especially when fluid change intervals are missed or during heavy use; even
during abuse. Drivers can count on AMSOIL Fuel Efficient ATF to provide
protection beyond conventional fluids.
| SERVICE LIFE |
|
|
| |
Recommendation for cars and light duty trucks
|
| Specification |
Normal Service*
|
Severe Service*
|
| DEXRON® VI |
100,000 miles (160,000 km)
|
50,000 miles (80,000 km)
|
| MERCON® LV, SP |
Follow vehicle manufacturer's recommendations
|
| Toyota WS |
100,000 miles (160,000 km)
|
60,000 miles (96,000 km)
|
HEALTH & SAFETY
This product is not expected to cause health concerns when used for the
intended application and according to the recommendations in the Material
Safety Data Sheet (MSDS). MSDS's are available upon request at 715-392-7101
or on our website.
Keep Out of Reach of Children. Don't pollute. Return used
oil to collection centers.
|
TYPICAL TECHNICAL PROPERTIES
|
|
AMSOIL Synthetic
Fuel Efficient Automatic Transmission Fluid (ATL)
|
|
Kinematic
Viscosity @ 100°C, cSt (ASTM D-445)
|
6.0
|
|
Kinematic
Viscosity @ 40°C, cSt (ASTM D-445)
|
29.8
|
|
Viscosity Index
(ASTM D-2270)
|
153
|
|
Flash Point
°C (°F) (ASTM D-92)
|
226 (439)
|
|
Fire Point °C
(°F) (ASTM D-92)
|
244 (471)
|
|
Pour Point °C
(°F) (ASTM D-97)
|
-53 (-63)
|
|
Four Ball
Wear Test @ 75°C, 1200 rpm, 40 kg, 1 hr, Scar, mm (ASTM D-4172)
|
0.40
|
|
Brookfield
Viscosity, cP (ASTM D-2983)
|
9050
|
|
Copper
Corrosion, 150°C, 3 hr (ASTM D-130)
|
1b
|
